Page 376 of 379 FirstFirst ... 276326366374375376377378 ... LastLast
Results 3,751 to 3,760 of 3790

Thread: The OT thread V1

  1. #3751
    Insider imped4now's Avatar
    Join Date
    Feb 2015
    Location
    Indianapolis
    Posts
    299
    Quote Originally Posted by cockerpunk View Post
    you mean the wrangler they forgot to weld the anti-roll bar brackets to the frame on?

    #justchryslerthings




    also not to put fine a point on it, but im pretty sure my miata has done more off roading than the vast majority of jeeps
    Well, it's good that I'm a good weldor (the correct spelling of one who welds) and actually have real, legitimate offroad experience of my own, as well as teaching others.
    OlllllllO

  2. #3752
    Insider Pump Scout's Avatar
    Join Date
    Apr 2012
    Location
    Wisconsin Rapids, WI, USA
    Posts
    812
    Quote Originally Posted by Fred View Post
    I really think a Jeep Wrangler or Gladiator is going to be my next vehicle... change my mind?
    Easy. I see the cost-to-the-dealership for extended warranties. Anything from FCA is always - ALWAYS - significantly more expensive than anything else you can get that isn't a highline brand or an exotic. It's not so much the mechanical stuff, which they've gotten better with. It electrical. Forever frickin' breaking down. And accordingly expensive.

    Quote Originally Posted by cockerpunk View Post
    FCA is a pile of junk and no one should ever buy anything they make. Jeeps have not been good in 25 years.

    done and done.
    Can't argue with this one. Absolute rubbish these days, unfortunately.

  3. #3753
    Insider imped4now's Avatar
    Join Date
    Feb 2015
    Location
    Indianapolis
    Posts
    299
    Again, I can only speak from my direct experience working for and owning FCA vehicles - I've never had a single electronic issue that wasn't directly caused by my own doing.

    For example, before I ditched the factory fuel tank in favor of a cell behind the seats in my TJ crawler, I came down on a rock so hard that it pushed the fuel pump out the top of the tank. I killed the pump and inverted the pump dimple in my gas tank skid plate. A pressed dimple in a 1/4" steel plate (not factory skid). At that time, I was the first and only person to have ever done that to one of these skids, so it was a hard impact.

    I've been involved in supplier quality audits for wire harnesses. They don't use junk electronics, I can tell you that. The controls on the assembly line are impressive....they don't build junk. The Toledo plant is without a doubt the best FCA plant I've been to in terms of culture, employee knowledge, employee GAS (give a shit), and overall documentation organization. Out of the FCA vehicles, I've got the most confidence in Jeeps (Wranglers) and Rams. The Pacifica line is also very impressive (located in Windsor, Canada) but I have no interest in minivans.

    The wife's 14 JKU has been flawless. My 12 JK was flawless. My 04 TJ was flawless before it became a street legal buggy, and even after that there were no issues that weren't caused by me. There are a lot of later model Jeeps in my circle of friends and family - no issues that I'm aware of, which I would be. I'm friends with the Kahlo family (Kahlo Jeep in Indy) and have had conversations with them about warranty and repair frequency. The JK's were low hitters and so far the JL's have been, as well. FCA has plenty of haters, deservedly so, but not all of their products are junk. If you really want to form an opinion, go spend some time analyzing a new Jeep inside and out, drive one, etc. They're pretty damn solid.
    Last edited by imped4now; 03-22-2019 at 02:22 PM.
    OlllllllO

  4. #3754
    Insider new ion?'s Avatar
    Join Date
    Feb 2013
    Location
    Victoria, BC
    Posts
    1,273
    Supports Inception Designs
    Just had to perform the Heimlich Maneuver on someone.

    It's a weird feeling.

  5. #3755
    Insider Unfated33's Avatar
    Join Date
    Jan 2013
    Location
    Charlotte, NC
    Posts
    760
    You were successful? If so, the feeling I have is relief. Glad you were there.

  6. #3756
    Insider new ion?'s Avatar
    Join Date
    Feb 2013
    Location
    Victoria, BC
    Posts
    1,273
    Supports Inception Designs
    Yes, everyone is fine.

    However, I just keep running the scenario through my head: should I have started with other things first? I did kind of jump straight to it....

    Then again, I was also the only person doing anything to help so I guess it's fine?

  7. #3757
    If the person in question wasn't choking on anything when you started to perform the Heimlich maneuver, I'd say you probably should've started with something else.

    Otherwise, since everyone came out fine, I think you did the right thing. If I had to guess, I'd think that inaction of bystanders is usually worse than the wrong action by bystanders.

  8. #3758
    This is kinda one of those things that it's so out of norm, so out of kilter in an everyday life, that it has you gobsmacked. Its ok. It ended well. You saved a life, that person is alive and no one served you papers for simple assault.

  9. #3759
    Insider PBSteve's Avatar
    Join Date
    May 2012
    Location
    Los Angeles
    Posts
    2,866
    Fun story: Henry Heimlich went off the reservation in the 80's.

    https://knowledgenuts.com/2014/09/22...enry-heimlich/
    Comfort the afflicted and afflict the comfortable.
    I work for the company building the Paragon...once we figure out a name

  10. #3760
    Insider
    Join Date
    Apr 2012
    Posts
    291
    Pricing on the Gladiator came out, as cool as a convertible truck is, I think it?s priced to shore up FCAs bottom line, not what it?s worth... guess we?ll see, but the Rubicon starting at 45k gets really expensive with just a few option boxes ticked.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •