Results 1 to 6 of 6

Thread: F-1 Illustrator Striker Spring Guide

  1. #1
    Insider Davros's Avatar
    Join Date
    Dec 2013
    Location
    Halifax, Nova Scotia
    Posts
    451
    Supports Inception Designs

    F-1 Illustrator Striker Spring Guide

    Hello, all.

    I cannot account for the Striker Spring Guide for my F-1 Illustrator. This is a guide rod/pin inside the spring in the lower tube. Item number 6 in the manual's parts breakdown page, part number 1010.

    Looking for help in getting a replacement. Is there something from a hardware that should do if it is the right length? Does anyone have dimensions for that by chance? While I can guess from having seen it so much I never actually measured it. Perhaps someone happens to know that a similar part to a different marker will work and will speak up.

    If I have to I will look for a used whole marker and buy it on Ebay or Kijiji or some-such and extract the guide from it. It would be nice to not have to go through that though.

    Scan of the manual: http://www.vintagerex.com/pics/gunpi...1%20Manual.pdf


    On a far less important note my detent is weakening. I think I found a source for one, but I would like to know in general if anyone happens to know if detents from other markers would work. If you know please advise. It is a style that I think was used on other markers.

    Here is an image
    https://www.baccipaintball.com/media...s/fst139_1.jpg

    I can probably buy one from Bacci Paintball but it would be good for fixes in the future if I knew of markers with compatible detents.

    The manual says to tighten the screw that holds in the detent spring to give it more holding power but it really feels like I will strip it if I keep going every time I attempt to drive the screw in more. Also, I do not know for sure if it will help at all.


    The detent thing is very minor. Really need help on the guide pin situation though.

    Any advice or further knowledge on the subject is welcome. Thanks.

  2. #2
    Insider Unfated33's Avatar
    Join Date
    Jan 2013
    Location
    Charlotte, NC
    Posts
    687
    Hmm, I don't know if it will work, but I've seen a similar part in Azodin markers. I'm really concerned the dimensions won't be the same, though. Look on page 6 of this link for part Z012:

    http://www.azodin.com/Support/MANUALS/KDII_MANUAL.pdf

    They sell it on their webstore for $5: http://store.azodin.com/index.php?ro...=zero+cup+seal

    I imagine there are another handful of poppet markers that use something similar.

    EDIT: Just realized it doesn't sit as far into the spring as I realized for the Azodin model: http://www.azodin.com/Support/Zero_R...ng_System.html

    2nd EDIT: Try these? https://www.baccipaintball.com/fst108.html
    Last edited by Unfated33; 10-18-2018 at 02:39 PM.

  3. #3
    Insider
    Join Date
    Apr 2012
    Location
    Knoxville, TN
    Posts
    2,234
    Sadly, I have fixed that with a nail before, and a bit of grinding. It is not a real high tolerance part. Try the azodin one first, but as long as the spring fits around it and it doesn't impact when you cycle it you should be fine.
    Josh Coray
    J4 Paintball
    Lead Design
    www.j4paintball.com

  4. #4
    Insider Davros's Avatar
    Join Date
    Dec 2013
    Location
    Halifax, Nova Scotia
    Posts
    451
    Supports Inception Designs
    Unfated, thanks for the second link. I was on Bacci but did not see that. It appears they were listed under "ACI" not "F1" parts where I understandably was looking.

    Josh, thank you. In the short term maybe I will do something like that. Telling me you actually experimented with that approach gives me confidence it is worth trying to use things like the Azodin part Unfated mentioned or a general piece from a hardware place.

    Still it would be great if I had measurements of an actual part.

    Thanks guys. More advice welcome, but the above is very helpful.

  5. #5
    I think what Josh did was pre-internet or just in the wilds of Alaska or readily available replacement parts. But lots of DIY parts started as field expedient repairs to get people back on the field with whatever they have.

  6. #6
    Insider
    Join Date
    Apr 2012
    Location
    Knoxville, TN
    Posts
    2,234
    Oh, we had internet. Just barely - but back in the early 90's and having to ship something out of Alaska was a $50 service fix when you included shipping, so, well, I have a grinder, a drill and this here screw...

    In fact, a lot of Alaska is that way so it was fairly normal to have a ton of parts around (read that as Junk) and to be ready to fix something as needed. We had some really janky setups. Then we met Doc and things got interesting. Good times.
    Josh Coray
    J4 Paintball
    Lead Design
    www.j4paintball.com

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •